View

View

View

View

View

View

View

View

The Westport Fire District has taken delivery of a 16 foot non walk in aluminum rescue. The truck features ROM roll up doors, a Honda 5,000 watt generator, Fire Research lights, bottle storage for 16 bottles and several roll out trays. The unit is a Bodyguard, Responder series built by V.R.S.
Sales.

View

Hensonville has taken delivery of a new Fire One brush truck. The unit is built on a Ford 450, 4X4 chassis. The body is an all aluminum Brush Master body with a 300 gallon tank and Hale pump.

View

View

Is a non walk-in rescue built on a 550 ford 4x4. The body was built by Fire One with the final assembly by V.R.S. Sales. It features slide out drop down trays, bottle storage for 10 SCBA bottles and fire research 300 watt 12 volt lights. This truck sold for under $70,000.00 and is the departments second truck from V.R.S.

This is a compressed air foam system built by Boise Mobile Equipment. The unit has a cross mount skid unit with a 350 GPM pump and a 75 CFM compressor. The foam system is a 1600 series foam pro. It is powered by a 55 HP Volks Wagon Diesel Engine. The tank is a 375 GPM with a 15 gallon foam tank. The body was built by Fire One

Germantown New York has received a new 18 foot rescue from Boise Mobile Equipment on a Kenworth chassis. The truck features a 25kw pto generator, Will Burt light tower, cascade system with a control panel and duel tank fragmentation container. The truck also has a receiver hitches on all four sides and a 5,000# portable winch as well as a 220 volt hydraulic power plant with three reels.

This is a new compressed air foam unit built by Snuffer. This truck is designed by V.R.S. Sales to handle car fires in the multi story parking garage as well as outside fires at the airport. The CAFS unit is set up to use class "A" foam and has a 150 gallon poly tank and a 10 gallon foam tank.

This is a small compressed air foam truck from Boise mobile equipment. It has a 350 gallon water tank with a 15 gallon foam tank. The pump package features a 110 GPM pump rated at 150 PSI and a 35 CFM compressor from Van Air. The foam proportioner is from Hale. The body is all aluminum with roll up doors. As you can see from the rear picture there is plenty of room for storage. The chassis is a 550 Ford.

This is a 2000 gallon semi-elliptical aluminum tanker. The truck features a 550GPM CET pump that is plumped to the tank with a pre-connect to the rear of the body there are three electric 10" newton dumps controlled for the can as well as by the dump itself. It is on a GMC top kick chassis with NA 300 CAT engine and an Allison transmission. This is the third truck purchased from V.R.S. Sales.

This is a 4x4 international built by Boise Mobil Eqipment. It Features a compressed air foam system a 500 GPM PTO pump and a 500 gallon tank the body is aluminum and the foam system is built by Boise with a 2001 foam pro system.

This is a Boise Mobile Equipment truck on a 4800 4x4 international. It features a 1250 GPM Q-Flow pump aluminum body and a 2001 foam pro system. The ladder rack is a zico quick lift and there is a front suction.

This is built by Boise Mobile Equipment and has 185 CFM compressed air foam system. The body is stainless steel with a 1,000 gallon rectangular tank with full depth compartments. The pump is a midship mounted 1,250 with the pump controls in the left rear compartment. The overall length of this is 26'. The chassis has a 10" extension with two SCBA seats in the cab. This is the third unit purchased from V.R.S. for this department.

This is a 750 G.P.M. water supply pump built by Boise Mobile Equipment. The chassis is a Ford 450 with a 84" CA. The body is aluminum and has a hose bed capacity of 1,700 feet of 5" hose. The side compartments are built to hold two portable pumps and strainers. The truck does not carry any water.

This truck was built by Boise Mobile Equipment and delivered in August, 2000. It features an aluminum body, 1000 gallon rectangular tank with full depth compartments. The hale pump is a 1250 QSMG with electric MIV valves. The chassis features a 430 hp cummins with a jake break and a 4060 transmission. This unit is stationed in the west end firehouse.

This is a Minipumper featuring a 750 Hale midship pump with a 300 gallon booster tank. The pump features a 4" discharge on the right side and roll up doors for the pump panels. There are two preconnects over the left side compartment, the hosebed can hold 800' of 4" hose and there is storage for 4 lengths of 5" hose under the hosebed. The body is manufactured from 3/16" aluminum. The chassis is a 550 Ford

This is a Boise Mobile Equipment C.A.F.S. pumper. The truck features a 1250 hale pump, 1500 gallon booster tank, 10" Newton dump, 2001 Foam Pro system, and a 185 CFM compressor. The body is aluminum with full height with a top mounted pump panel. Compartments left side.

This is a stainless steel pumper with a Hale Q-Flow pump. This truck was built by V-Tec of Vermont and features a bolted body. It is top mounted controls and is on a 4900 sseries international with a 300 HP engine.

This is a compressed air foam truck with rear mounted 1,000 gallon per minute pump and a 500 gallon tank. The Truck is designed for quick attack and has full depth compartments. The chassis is a 4800 4x4 international. It was built by V-Tec of Vermont.